root@Taiyear:/#
U-Boot 1.1.3 (Dec 27 2013 - 09:14:28)
SoC:MediaTek MT7620
DRAM: Memory Testing..65536K OK. is 64 MB
relocate_code Pointer at: 83fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 14
spi device id: ef 40 18 0 0 (40180000)
Flash: W25Q128BV
*** Warning - bad CRC, using default environment
_______________________________________________________________
| ____ _ ____ |
| | _ __ _ _ __ __| | ___ _ __ __ _| __ ) _____ __ |
| | |_) / _` | '_ / _` |/ _ | '__/ _` | _ / _ / / |
| | __/ (_| | | | | (_| | (_) | | | (_| | |_) | (_) > < |
| |_| \__,_|_| |_|\__,_|\___/|_| \__,_|____/ \___/_/\_ |
| |
| Ralink/MTK SDK Plantform |
| Copyright 2005-2013 |
| Board:ZBT WR8305RT |
| |
| lintel<lintel.huang@gmail.com> |
|______________________________________________________________|
===============System Info==================
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Flash component: SPI Flash
CPU Speed: 580 MHZ
RAM Size:64 Mbytes
Build Date:Dec 27 2013 Time:09:14:28
============================================
GPIO Init:
UARTF_SHARE_MODE:GPIO
I2C_GPIO_MODE:GPIO
GPIO_MODE_REG:0x1a311d
ReadyLED Bit:0x1
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
Press Reset button enter upgrade mode!
## Booting image at bc050000 ...
Image Name: PandoraBox Linux-3.3.8
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 993659 Bytes = 970.4 kB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
PandoraBox For Ralink SoC. Copyright 2005-2013 Lintel<lintel.huang@gmail.com>
Linux Kernel started...
THIS IS ASIC
[ 0.000000] Linux version 3.3.8 (taiyear@taiyear) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Thu Sep 25 15:12:16 CST 2014
[ 0.000000] Board has DDR2
[ 0.000000] MediaTek MT7620N CPU:580MHz, Bus:193MHz Uart:40MHz
[ 0.000000] Boot form:SPI FLASH
[ 0.000000] MIPS CPU sleep mode enabled.
[ 0.000000] Detecting memory...64 MB!
[ 0.000000] PCIE: bypass PCIe DLL.
[ 0.000000] PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
[ 0.000000] disable all power about PCIe
[ 0.000000] PCIE: PLL power down for MT7620N
[ 0.000000] CPU revision is: 00019650 (MIPS 24KEc)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS1,115200n8 board=TY7620NI rootfstype=squashfs
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=000464a0
[ 0.000000] Readback ErrCtl register=000464a0
[ 0.000000] Memory: 61752k/65536k available (2371k kernel code, 3784k reserved, 393k data, 168k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=16, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:128
[ 0.000000] MTK/Ralink System Tick Counter init... cd:802a47c0, m:214748, s:32
[ 0.000000] console [ttyS1] enabled
[ 0.004000] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
[ 0.040000] pid_max: default: 32768 minimum: 301
[ 0.044000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.052000] Ralink/MTK BootROM maped.
[ 0.056000] MIPS: machine is TY-7620N-1
[ 0.060000] Ralink Board GPIO_MODE init:
[ 0.064000] I2C:GPIO
[ 0.064000] SPI_REFCLK:GPIO
[ 0.068000] UART_F:GPIO
[ 0.068000] GPIO_MODE_REGs: 0x1a311d
[ 0.072000] ralink_register_flash:SPI Flash.
[ 0.076000] Ralink/MTK ILL_ACC driver for MediaTek MT7620N Board. Copyright 2013 (C) lintel
[ 0.080000] illegal access irq registered.
[ 0.084000] General GPIO Driver for MediaTek MT7620N Board. Copyright lintel 2005-2013
[ 0.088000] gpiochip_add: registered GPIOs 0 to 23 on device: MT7620-GPIO0
[ 0.092000] gpiochip_add: registered GPIOs 24 to 39 on device: MT7620-GPIO1
[ 0.096000] gpiochip_add: registered GPIOs 40 to 71 on device: MT7620-GPIO2
[ 0.100000] gpiochip_add: registered GPIOs 72 to 95 on device: MT7620-GPIO3
[ 0.200000] MT7620 PPLL unlock
[ 0.212000] bio: create slab <bio-0> at 0
[ 0.216000] Switching to clocksource Ralink external timer
[ 0.220000] NET: Registered protocol family 2
[ 0.224000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.232000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.240000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.248000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.252000] TCP reno registered
[ 0.256000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.264000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.268000] NET: Registered protocol family 1
[ 0.276000] Ralink SoC clocks api init.
[ 0.280000] Ralink GPIODEV resource maped.
[ 0.284000] Load Ralink Timer0 Module
[ 0.288000] Load Ralink Timer1 Module
[ 0.292000] RT3xxx EHCI/OHCI init.
[ 0.312000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.316000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZO) (LZMA) (RTIME) (RUBIN) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.332000] msgmni has been set to 120
[ 0.336000] io scheduler noop registered
[ 0.340000] io scheduler deadline registered (default)
[ 0.344000] io scheduler cfq registered
[ 0.348000] Ralink DMA Engine API Enable .
[ 0.352000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.360000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
[ 0.368000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
[ 0.376000] Enable Ralink GDMA Controller Module
[ 0.380000] GDMA IP Version=3
[ 0.388000] loop: module loaded
[ 0.392000] Ralink SPI flash Driver for PandoraBox.
[ 0.400000] deice id : ef 40 18 0 0 (40180000)
[ 0.404000] W25Q128BV(ef 40180000) (16384 Kbytes)
[ 0.408000] mtd .name = raspi, .size = 0x01000000 (0M) .erasesize = 0x00000010 (0K) .numeraseregions = 65536
[ 0.420000] Creating 5 MTD partitions on "raspi":
[ 0.424000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.428000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.436000] 0x000000040000-0x000000050000 : "Factory"
[ 0.444000] 0x000000000000-0x000001000000 : "fullflash"
[ 0.452000] 0x000000050000-0x000001000000 : "firmware"
[ 0.456000] Creating 2 MTD partitions on "raspi":
[ 0.464000] 0x000000050000-0x000000150000 : "kernel"
[ 0.468000] 0x000000150000-0x000001000000 : "rootfs"
[ 0.476000] mtd: partition "rootfs" set to be root filesystem
[ 0.480000] mtd: partition "rootfs_data" created automatically, ofs=4E0000, len=B20000
[ 0.492000] 0x0000004e0000-0x000001000000 : "rootfs_data"
[ 0.500000] rdm_major = 253
[ 0.500000] EEPROM:Read from [Factory] offset 0x28,length 0x6.
[ 0.508000] Ralink APSoC Ethernet Driver v3.0.6. Rx Ring: 256, Tx Ring: 256. Max packet size: 1536.
[ 0.516000] raeth: disable ESW ports on driver init.
[ 0.524000] mt762x-gsw switch driver registered.
[ 0.528000] Ralink APSoC Hardware Watchdog Timer
[ 0.532000] SDHC Interface init.
[ 0.540000] mtk-sd: MediaTek MT76xx MSDC Driver
[ 0.544000] TCP cubic registered
[ 0.548000] NET: Registered protocol family 17
[ 0.552000] 8021q: 802.1Q VLAN Support v1.8
[ 0.564000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[ 0.572000] Freeing unused kernel memory: 168k freed
##### MediaTek MT76xx ESW VLAN Partition(LLLLW) #####
switch reg write offset=2004, value=ff0003
switch reg write offset=2104, value=ff0003
switch reg write offset=2204, value=ff0003
switch reg write offset=2304, value=ff0003
switch reg write offset=2404, value=ff0003
switch reg write offset=2504, value=ff0003
switch reg write offset=2010, value=810000c0
switch reg write offset=2110, value=810000c0
switch reg write offset=2210, value=810000c0
switch reg write offset=2310, value=810000c0
switch reg write offset=2410, value=810000c0
switch reg write offset=2510, value=810000c0
switch reg write offset=2610, value=81000000
switch reg write offset=2710, value=81000000
switch reg write offset=2604, value=20ff0003
switch reg write offset=2704, value=20ff0003
Special Tag Disabled
switch reg write offset=2610, value=81000000
switch reg write offset=2014, value=10001
switch reg write offset=2114, value=10001
switch reg write offset=2214, value=10001
switch reg write offset=2314, value=10001
switch reg write offset=2414, value=10002
switch reg write offset=2514, value=10001
REG_ESW_WT_MAC_ATC is 0x7ff0002
done.
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 5.640000] JFFS2 notice: (447) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (0 unchecked, 1 orphan) and 32 of xref (0 dead, 17 orphan) found.
switching to jffs2
- init -
Please press Enter to activate this console. [ 7.068000] Uniform Multi-Platform E-IDE driver
[ 7.320000] SCSI subsystem initialized
[ 7.456000] usbcore: registered new interface driver usbfs
[ 7.464000] usbcore: registered new interface driver hub
[ 7.472000] usbcore: registered new device driver usb
[ 7.816000] PPP generic driver version 2.4.2
[ 7.852000] gpiodev: gpio device registered with major 254
[ 7.868000] ide-gd driver 1.18
[ 8.128000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 8.440000] NET: Registered protocol family 24
[ 8.608000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.632000] rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
[ 8.640000] rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
[ 8.672000] rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
[ 8.688000] rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
[ 8.692000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 8.700000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.708000] usb usb1: Product: Ralink EHCI Host Controller
[ 8.712000] usb usb1: Manufacturer: Linux 3.3.8 ehci_hcd
[ 8.716000] usb usb1: SerialNumber: rt3xxx
[ 8.724000] hub 1-0:1.0: USB hub found
[ 8.728000] hub 1-0:1.0: 1 port detected
[ 8.988000] sata_sis: Unknown symbol sis_info133_for_sata (err 0)
[ 9.008000] nf_conntrack version 0.5.0 (967 buckets, 3868 max)
[ 9.932000] xt_time: kernel timezone is -0000
[ 10.692000] rt2860v2_ap: module license 'Proprietary' taints kernel.
[ 10.700000] Disabling lock debugging due to kernel taint
[ 10.732000] PanddoraBox AP Driver version-2.7.1.6(Sep 25 2014 14:15:18).
[ 10.840000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 10.856000] mmc_spi: Unknown symbol mmc_spi_get_pdata (err 0)
[ 10.864000] mmc_spi: Unknown symbol mmc_spi_put_pdata (err 0)
[ 14.860000] raeth: HW VLAN TX offload enabled
[ 14.860000] raeth: HW IP/TCP/UDP checksum offload enabled
[ 14.860000] raeth: HW Scatter/Gather TX offload enabled
[ 14.860000] raeth: HW TCP segmentation offload (TSO) enabled
[ 14.908000] device eth2.1 entered promiscuous mode
[ 14.912000] device eth2 entered promiscuous mode
[ 14.920000] br-lan: port 1(eth2.1) entered forwarding state
[ 14.924000] br-lan: port 1(eth2.1) entered forwarding state
[ 16.788000] Started WatchDog Timer.
[ 16.792000] Started WatchDog Timer.
[ 16.928000] br-lan: port 1(eth2.1) entered forwarding state
[ 19.352000] EEPROM:Read from [Factory] offset 0x0,length 0x200.
[ 22.284000] 0x1300 = 00064380
[ 23.200000] device ra0 entered promiscuous mode
[ 23.204000] br-lan: port 2(ra0) entered forwarding state
[ 23.212000] br-lan: port 2(ra0) entered forwarding state
[ 25.216000] br-lan: port 2(ra0) entered forwarding state
[ 29.312000] str_var www.wifi-union.cn?rmac=00:01:42:91:19:94.
[ 29.316000] netlink create success ,webauth moudle started
[ 29.324000] size = 0
BusyBox v1.19.4 (2014-09-25 14:20:05 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
______________________________________________________________
| _ _ _ _ _ _ |
| | |_ ___ (_)\ //__ ___ _ ___ | |_ ___ ___| |__ |
| | __/ _ _ \// _ / _ \// | __/ _ / __| '_ |
| | ||||_| | | || __/||_| || | || __/ (__| | | |_ |
| \__\___/\|_| ||\___|\___/\|| \__\___|\___|_| |_(_) |
| |
| |
| Copyright 2013 - 2014 |
| MICHAEL (Michael.xu@taiyear.com) |
|_____________________________________________________________ |
Base on OpenWrt (12.09.2, R1)
root@Taiyear:/#
root@Taiyear:/#
root@Taiyear:/#
root@Taiyear:/# uname -r
3.3.8
root@Taiyear:/# date
Thu Sep 25 14:38:40 CST 2014
root@Taiyear:/#
root@Taiyear:/# ls
bin dev etc_ro mnt proc root sys usr www
config etc lib overlay rom sbin tmp var
root@Taiyear:/#
U-Boot 1.1.3 (Dec 27 2013 - 09:14:28)
SoC:MediaTek MT7620
DRAM: Memory Testing..65536K OK. is 64 MB
relocate_code Pointer at: 83fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 14
spi device id: ef 40 18 0 0 (40180000)
Flash: W25Q128BV
*** Warning - bad CRC, using default environment
_______________________________________________________________
| ____ _ ____ |
| | _ __ _ _ __ __| | ___ _ __ __ _| __ ) _____ __ |
| | |_) / _` | '_ / _` |/ _ | '__/ _` | _ / _ / / |
| | __/ (_| | | | | (_| | (_) | | | (_| | |_) | (_) > < |
| |_| \__,_|_| |_|\__,_|\___/|_| \__,_|____/ \___/_/\_ |
| |
| Ralink/MTK SDK Plantform |
| Copyright 2005-2013 |
| Board:ZBT WR8305RT |
| |
| lintel<lintel.huang@gmail.com> |
|______________________________________________________________|
===============System Info==================
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Flash component: SPI Flash
CPU Speed: 580 MHZ
RAM Size:64 Mbytes
Build Date:Dec 27 2013 Time:09:14:28
============================================
GPIO Init:
UARTF_SHARE_MODE:GPIO
I2C_GPIO_MODE:GPIO
GPIO_MODE_REG:0x1a311d
ReadyLED Bit:0x1
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
Press Reset button enter upgrade mode!
## Booting image at bc050000 ...
Image Name: MIPS OpenWrt Linux-3.10.49
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1035008 Bytes = 1010.8 kB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 3.10.49 (haijie@xxx.dev.xxxxx) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44550) ) #1 Wed Mar 25 23:09:48 CST 2015
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: Ralink MT7620N ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Zbtlink ZBT-WA05
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=000190af
[ 0.000000] Readback ErrCtl register=000190af
[ 0.000000] Memory: 61648k/65536k available (2300k kernel code, 3888k reserved, 556k data, 212k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.070000] pinctrl core: initialized pinctrl subsystem
[ 0.070000] NET: Registered protocol family 16
[ 0.100000] bio: create slab <bio-0> at 0
[ 0.100000] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.110000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.110000] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.120000] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.120000] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.130000] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.130000] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.140000] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.140000] Switching to clocksource MIPS
[ 0.150000] NET: Registered protocol family 2
[ 0.150000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.160000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.170000] TCP: Hash tables configured (established 512 bind 512)
[ 0.170000] TCP: reno registered
[ 0.180000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.190000] NET: Registered protocol family 1
[ 0.190000] rt-timer 10000100.timer: maximum frequncy is 2441Hz
[ 0.220000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.220000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.230000] msgmni has been set to 120
[ 0.240000] io scheduler noop registered
[ 0.240000] io scheduler deadline registered (default)
[ 0.250000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.250000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A
[ 0.260000] console [ttyS0] enabled, bootconsole disabled
[ 0.260000] console [ttyS0] enabled, bootconsole disabled
[ 0.280000] m25p80 spi32766.0: found w25q128, expected w25q64
[ 0.280000] m25p80 spi32766.0: w25q128 (16384 Kbytes)
[ 0.290000] 4 ofpart partitions found on MTD device spi32766.0
[ 0.290000] Creating 4 MTD partitions on "spi32766.0":
[ 0.300000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.310000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.310000] 0x000000040000-0x000000050000 : "factory"
[ 0.320000] 0x000000050000-0x0000007b0000 : "firmware"
[ 0.330000] 0x00000014cb40-0x0000007b0000 : "rootfs"
[ 0.330000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.350000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.350000] mtd: partition "rootfs_data" created automatically, ofs=0x5f0000, len=0x1c0000
[ 0.360000] 0x0000005f0000-0x0000007b0000 : "rootfs_data"
[ 0.370000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 0.380000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
[ 0.390000] rt3xxx-usbphy usbphy.3: loaded
[ 0.390000] rt2880_wdt 10000120.watchdog: Initialized
[ 0.400000] TCP: cubic registered
[ 0.400000] NET: Registered protocol family 17
[ 0.410000] 8021q: 802.1Q VLAN Support v1.8
[ 0.420000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.430000] Freeing unused kernel memory: 212K (802cb000 - 80300000)
procd: Console is alive
procd: - watchdog -
[ 4.370000] usbcore: registered new interface driver usbfs
[ 4.380000] usbcore: registered new interface driver hub
[ 4.380000] usbcore: registered new device driver usb
[ 4.400000] SCSI subsystem initialized
[ 4.410000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.420000] ehci-platform: EHCI generic platform driver
[ 4.620000] rt3xxx-usbphy usbphy.3: remote usb device wakeup disabled
[ 4.630000] rt3xxx-usbphy usbphy.3: UTMI 16bit 30MHz
[ 4.640000] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 4.640000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 4.650000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 4.680000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 4.680000] hub 1-0:1.0: USB hub found
[ 4.690000] hub 1-0:1.0: 1 port detected
[ 4.690000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.700000] ohci-platform 101c1000.ohci: Generic Platform OHCI Controller
[ 4.710000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 4.710000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 4.780000] hub 2-0:1.0: USB hub found
[ 4.780000] hub 2-0:1.0: 1 port detected
[ 4.790000] leds-gpio gpio-leds.4: pins are not configured from the driver
[ 4.800000] usbcore: registered new interface driver usb-storage
procd: - preinit -
[ 5.450000] 8021q: adding VLAN 0 to HW filter on device eth0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 9.510000] jffs2: notice: (294) jffs2_build_xattr_subsystem: complete building xattr subsystem, 21 of xdatum (0 unchecked, 20 orphan) and 59 of xref (0 dead, 40 orphan) found.
[ 9.530000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 9.530000] block: unable to load configuration (fstab: Entry not found)
[ 9.540000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 9.560000] block: extroot: not configured
jffs2 is ready
No jffs2 marker was found
[ 9.690000] jffs2: notice: (291) jffs2_build_xattr_subsystem: complete building xattr subsystem, 21 of xdatum (0 unchecked, 20 orphan) and 59 of xref (0 dead, 40 orphan) found.
[ 10.270000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 10.280000] block: unable to load configuration (fstab: Entry not found)
[ 10.280000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 10.300000] block: extroot: not configured
switching to overlay
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 12.410000] NET: Registered protocol family 10
[ 12.420000] l2tp_core: L2TP core driver, V2.0
[ 12.420000] l2tp_netlink: L2TP netlink interface
[ 12.440000] gre: GRE over IPv4 demultiplexor driver
[ 12.450000] ip_gre: GRE over IPv4 tunneling driver
[ 12.470000] u32 classifier
[ 12.470000] input device check on
[ 12.480000] Actions configured
[ 12.490000] Mirror/redirect action on
[ 12.510000] nf_conntrack version 0.5.0 (966 buckets, 3864 max)
[ 12.530000] Failed to load ipt action
[ 12.580000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 12.580000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 12.610000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.670000] usbcore: registered new interface driver ums-alauda
[ 12.690000] usbcore: registered new interface driver ums-cypress
[ 12.710000] usbcore: registered new interface driver ums-datafab
[ 12.710000] usbcore: registered new interface driver ums-freecom
[ 12.730000] usbcore: registered new interface driver ums-isd200
[ 12.730000] usbcore: registered new interface driver ums-jumpshot
[ 12.760000] usbcore: registered new interface driver ums-karma
[ 12.780000] usbcore: registered new interface driver ums-sddr09
[ 12.800000] usbcore: registered new interface driver ums-sddr55
[ 12.800000] usbcore: registered new interface driver ums-usbat
[ 12.830000] usbcore: registered new interface driver usblp
[ 12.880000] xt_time: kernel timezone is -0000
[ 12.910000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.930000] cfg80211: World regulatory domain updated:
[ 12.930000] cfg80211: DFS Master region: unset
[ 12.940000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 12.940000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.950000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.960000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.970000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.980000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 12.990000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 12.990000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 13.000000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 13.060000] PPP generic driver version 2.4.2
[ 13.070000] PPP MPPE Compression module registered
[ 13.070000] NET: Registered protocol family 24
[ 13.080000] PPTP driver version 0.8.5
[ 13.100000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 13.120000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected
[ 13.130000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 19.390000] 8021q: adding VLAN 0 to HW filter on device eth0
[ 19.400000] device eth0.1 entered promiscuous mode
[ 19.400000] device eth0 entered promiscuous mode
[ 19.420000] br-lan: port 1(eth0.1) entered forwarding state
[ 19.420000] br-lan: port 1(eth0.1) entered forwarding state
[ 21.420000] br-lan: port 1(eth0.1) entered forwarding state
BusyBox v1.22.1 (2015-03-25 23:06:14 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Barrier Breaker, r44874)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@OpenWrt:/# procd: - init complete -
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/# ifconfig
br-lan Link encap:Ethernet HWaddr 78:A3:51:02:55:CE
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::7aa3:51ff:fe02:55ce/64 Scope:Link
inet6 addr: fd85:6771:bda1::1/60 Scope:Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:51 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:6520 (6.3 KiB)
eth0 Link encap:Ethernet HWaddr 78:A3:51:02:55:CE
inet6 addr: fe80::7aa3:51ff:fe02:55ce/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:70 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:11813 (11.5 KiB)
Interrupt:5
eth0.1 Link encap:Ethernet HWaddr 78:A3:51:02:55:CE
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:52 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:6566 (6.4 KiB)
eth0.2 Link encap:Ethernet HWaddr 78:A3:51:02:55:CF
inet6 addr: fe80::7aa3:51ff:fe02:55cf/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:3486 (3.4 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:194 errors:0 dropped:0 overruns:0 frame:0
TX packets:194 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:13152 (12.8 KiB) TX bytes:13152 (12.8 KiB)