Pixhawk---通过串口方式加入一个自己定义传感器（超声波为例）

Pixhawk—加入一个自己定义传感器—超声波（串口方式）

1 说明

  首先超声波模块是通过串口方式发送（Tx）出数据，使用的模块数据发送周期为100ms，数据格式为：

R0034 R0122 R0122 R0046 R0127 R0044 R0044 R0125 R0034 R0037 R0041 R0122 R0122 .....

则能够通过Pixhawk板上的串口来接收（Rx）数据，即将超声波的Tx接口连接到Pixhawk板上的Rx接口。
  Pixhawk板上串口说明：
  这里写图片描写叙述
  測试使用Pixhawk板上TELEM2接口的USART2。相应的Nuttx UART设备文件尾/dev/ttyS2：
  这里写图片描写叙述

2 读取数据測试

  步骤：

  • 在Firmware/src/modules中加入一个新的目录。命名为rw_uart
  • 在rw_uart目录中创建module.mk文件，并输入下面内容：
    • MODULE_COMMAND = rw_uart
    • SRCS = rw_uart.c
  • 在rw_uart目录中创建rw_uart.c文件
  • 注冊新加入的应用到NuttShell中。Firmware/makefiles/nuttx/config_px4fmu-v2_default.mk文件里加入例如以下内容：
    • MODULES += modules/rw_uart

rw_uart.c

#include <stdio.h>
#include <termios.h>
#include <unistd.h>
#include <stdbool.h>
#include <errno.h>
#include <drivers/drv_hrt.h>

__EXPORT int rw_uart_main(int argc, char *argv[]);

static int uart_init(char * uart_name);
static int set_uart_baudrate(const int fd, unsigned int baud);

int set_uart_baudrate(const int fd, unsigned int baud)
{
    int speed;

    switch (baud) {
        case 9600:   speed = B9600;   break;
        case 19200:  speed = B19200;  break;
        case 38400:  speed = B38400;  break;
        case 57600:  speed = B57600;  break;
        case 115200: speed = B115200; break;
        default:
            warnx("ERR: baudrate: %d
", baud);
            return -EINVAL;
    }

    struct termios uart_config;

    int termios_state;

    /* fill the struct for the new configuration */
    tcgetattr(fd, &uart_config);
    /* clear ONLCR flag (which appends a CR for every LF) */
    uart_config.c_oflag &= ~ONLCR;
    /* no parity, one stop bit */
    uart_config.c_cflag &= ~(CSTOPB | PARENB);
    /* set baud rate */
    if ((termios_state = cfsetispeed(&uart_config, speed)) < 0) {
        warnx("ERR: %d (cfsetispeed)
", termios_state);
        return false;
    }

    if ((termios_state = cfsetospeed(&uart_config, speed)) < 0) {
        warnx("ERR: %d (cfsetospeed)
", termios_state);
        return false;
    }

    if ((termios_state = tcsetattr(fd, TCSANOW, &uart_config)) < 0) {
        warnx("ERR: %d (tcsetattr)
", termios_state);
        return false;
    }

    return true;
}


int uart_init(char * uart_name)
{
    int serial_fd = open(uart_name, O_RDWR | O_NOCTTY);

    if (serial_fd < 0) {
        err(1, "failed to open port: %s", uart_name);
        return false;
    }
    return serial_fd;
}

int rw_uart_main(int argc, char *argv[])
{
    char data = '0';
    char buffer[4] = "";
    /*
     * TELEM1 : /dev/ttyS1
     * TELEM2 : /dev/ttyS2
     * GPS    : /dev/ttyS3
     * NSH    : /dev/ttyS5
     * SERIAL4: /dev/ttyS6
     * N/A    : /dev/ttyS4
     * IO DEBUG (RX only):/dev/ttyS0
     */
    int uart_read = uart_init("/dev/ttyS2");
    if(false == uart_read)return -1;
    if(false == set_uart_baudrate(uart_read,9600)){
        printf("[YCM]set_uart_baudrate is failed
");
        return -1;
    }
    printf("[YCM]uart init is successful
");

    while(true){
        read(uart_read,&data,1);
        if(data == 'R'){
            for(int i = 0;i <4;++i){
                read(uart_read,&data,1);
                buffer[i] = data;
                data = '0';
            }
            printf("%s
",buffer);
        }
    }

    return 0;
}

  • 编译并刷固件

    • make clean
    • make upload px4fmu-v2_default

  • 查看app

    • 在NSH终端中输入help，在Builtin Apps中出现rw_uart应用。
  • 执行rw_uart应用（前提是模块与Pixhawk连接好）
    • 在NSH终端中输入rw_uart。回车，查看超声波的打印数据。

3 公布超声波的数据

  在无人机执行时，首先是要将应用随系统启动时就启动起来的。且将获得的超声波数据不断的公布出去，从而让其它应用得以订阅使用。这里也使用Pixhawk里面的通用模式，即主线程。检測app命令输入，创建一个线程来不断的公布数据。

3.1 定义主题和公布主题

  • 在modules/rw_uart目录下创建一个文件：rw_uart_sonar_topic.h

rw_uart_sonar_topic.h

#ifndef __RW_UART_SONAR_H_
#define __RW_UART_SONAR_H_

#include <stdint.h>
#include <uORB/uORB.h>

/*声明主题。主题名自己定义*/
ORB_DECLARE(rw_uart_sonar);

/* 定义要公布的数据结构体 */
struct rw_uart_sonar_data_s{
    char datastr[5];        //原始数据
    int data;               //解析数据。单位：mm
};

#endif

rw_uart.c

#include <stdio.h>
#include <termios.h>
#include <unistd.h>
#include <stdlib.h>
#include <string.h>
#include <stdbool.h>
#include <errno.h>
#include <drivers/drv_hrt.h>

#include "rw_uart_sonar_topic.h"

/* 定义主题 */
ORB_DEFINE(rw_uart_sonar, struct rw_uart_sonar_data_s);

static bool thread_should_exit = false;
static bool thread_running = false;
static int daemon_task;


__EXPORT int rw_uart_main(int argc, char *argv[]);
int rw_uart_thread_main(int argc, char *argv[]);

static int uart_init(const char * uart_name);
static int set_uart_baudrate(const int fd, unsigned int baud);
static void usage(const char *reason);



int set_uart_baudrate(const int fd, unsigned int baud)
{
    int speed;

    switch (baud) {
        case 9600:   speed = B9600;   break;
        case 19200:  speed = B19200;  break;
        case 38400:  speed = B38400;  break;
        case 57600:  speed = B57600;  break;
        case 115200: speed = B115200; break;
        default:
            warnx("ERR: baudrate: %d
", baud);
            return -EINVAL;
    }

    struct termios uart_config;

    int termios_state;

    /* fill the struct for the new configuration */
    tcgetattr(fd, &uart_config);
    /* clear ONLCR flag (which appends a CR for every LF) */
    uart_config.c_oflag &= ~ONLCR;
    /* no parity, one stop bit */
    uart_config.c_cflag &= ~(CSTOPB | PARENB);
    /* set baud rate */
    if ((termios_state = cfsetispeed(&uart_config, speed)) < 0) {
        warnx("ERR: %d (cfsetispeed)
", termios_state);
        return false;
    }

    if ((termios_state = cfsetospeed(&uart_config, speed)) < 0) {
        warnx("ERR: %d (cfsetospeed)
", termios_state);
        return false;
    }

    if ((termios_state = tcsetattr(fd, TCSANOW, &uart_config)) < 0) {
        warnx("ERR: %d (tcsetattr)
", termios_state);
        return false;
    }

    return true;
}


int uart_init(const char * uart_name)
{
    int serial_fd = open(uart_name, O_RDWR | O_NOCTTY);

    if (serial_fd < 0) {
        err(1, "failed to open port: %s", uart_name);
        return false;
    }
    return serial_fd;
}

static void usage(const char *reason)
{
    if (reason) {
        fprintf(stderr, "%s
", reason);
    }

    fprintf(stderr, "usage: position_estimator_inav {start|stop|status} [param]

");
    exit(1);
}

int rw_uart_main(int argc, char *argv[])
{
    if (argc < 2) {
        usage("[YCM]missing command");
    }

    if (!strcmp(argv[1], "start")) {
        if (thread_running) {
            warnx("[YCM]already running
");
            exit(0);
        }

        thread_should_exit = false;
        daemon_task = px4_task_spawn_cmd("rw_uart",
                         SCHED_DEFAULT,
                         SCHED_PRIORITY_MAX - 5,
                         2000,
                         rw_uart_thread_main,
                         (argv) ?
 (char * const *)&argv[2] : (char * const *)NULL);
        exit(0);
    }

    if (!strcmp(argv[1], "stop")) {
        thread_should_exit = true;
        exit(0);
    }

    if (!strcmp(argv[1], "status")) {
        if (thread_running) {
            warnx("[YCM]running");

        } else {
            warnx("[YCM]stopped");
        }

        exit(0);
    }

    usage("unrecognized command");
    exit(1);
}

int rw_uart_thread_main(int argc, char *argv[])
{

    if (argc < 2) {
        errx(1, "[YCM]need a serial port name as argument");
        usage("eg:");
    }

    const char *uart_name = argv[1];

    warnx("[YCM]opening port %s", uart_name);
    char data = '0';
    char buffer[5] = "";
    /*
     * TELEM1 : /dev/ttyS1
     * TELEM2 : /dev/ttyS2
     * GPS    : /dev/ttyS3
     * NSH    : /dev/ttyS5
     * SERIAL4: /dev/ttyS6
     * N/A    : /dev/ttyS4
     * IO DEBUG (RX only):/dev/ttyS0
     */
    int uart_read = uart_init(uart_name);
    if(false == uart_read)return -1;
    if(false == set_uart_baudrate(uart_read,9600)){
        printf("[YCM]set_uart_baudrate is failed
");
        return -1;
    }
    printf("[YCM]uart init is successful
");

    thread_running = true;

    /*初始化数据结构体 */
    struct rw_uart_sonar_data_s sonardata;
    memset(&sonardata, 0, sizeof(sonardata));
    /* 公告主题 */
    orb_advert_t rw_uart_sonar_pub = orb_advertise(ORB_ID(rw_uart_sonar), &sonardata);


    while(!thread_should_exit){
        read(uart_read,&data,1);
        if(data == 'R'){
            for(int i = 0;i <4;++i){
                read(uart_read,&data,1);
                buffer[i] = data;
                data = '0';
            }
            strncpy(sonardata.datastr,buffer,4);
            sonardata.data = atoi(sonardata.datastr);
            //printf("[YCM]sonar.data=%d
",sonardata.data);
            orb_publish(ORB_ID(rw_uart_sonar), rw_uart_sonar_pub, &sonardata);
        }
    }

    warnx("[YCM]exiting");
    thread_running = false;
    close(uart_read);

    fflush(stdout);
    return 0;
}

3.2 測试公布的主题—订阅主题

  測试能够随便一个启动的app中进行主题订阅，然后将订阅的数据打印出来。看是否是超声波的数据。这里測试是在固件的src/examples目录中的px4_simple_app应用进行測试的。

  • 将px4_simple_app应用加入到NuttShell中。

    Firmware/makefiles/nuttx/config_px4fmu-v2_default.mk文件里加入例如以下内容：

    • MODULES += examples/px4_simple_app
  • 在px4_simple_app.c中代码内容：
#include <px4_config.h>
#include <unistd.h>
#include <stdio.h>
#include <poll.h>
#include <string.h>

#include <uORB/uORB.h>
#include "rw_uart/rw_uart_sonar_topic.h"

__EXPORT int px4_simple_app_main(int argc, char *argv[]);

int px4_simple_app_main(int argc, char *argv[])
{
    printf("Hello Sky!
");

    /* subscribe to rw_uart_sonar topic */
    int sonar_sub_fd = orb_subscribe(ORB_ID(rw_uart_sonar));
    /*设置以一秒钟接收一次，并打印出数据*/
    orb_set_interval(sonar_sub_fd, 1000);
    bool updated;
    struct rw_uart_sonar_data_s sonar;

    /*接收数据方式一：start*/
    /*
    while(true){
        orb_check(sonar_sub_fd, &updated);

        if (updated) {
            orb_copy(ORB_ID(rw_uart_sonar), sonar_sub_fd, &sonar);
            printf("[YCM]sonar.data=%d
",sonar.data);
        }
        //else printf("[YCM]No soanar data update
");
    }
    */
    /*接收数据方式一：end*/

    /*接收数据方式二：start*/
    /* one could wait for multiple topics with this technique, just using one here */
    struct pollfd fds[] = {
        { .fd = sonar_sub_fd,   .events = POLLIN },
        /* there could be more file descriptors here, in the form like:
         * { .fd = other_sub_fd,   .events = POLLIN },
         */
    };

    int error_counter = 0;

    for (int i = 0; i < 5; i++) {s
        /* wait for sensor update of 1 file descriptor for 1000 ms (1 second) */
        int poll_ret = poll(fds, 1, 1000);

        /* handle the poll result */
        if (poll_ret == 0) {
            /* this means none of our providers is giving us data */
            printf("[px4_simple_app] Got no data within a second
");

        } else if (poll_ret < 0) {
            /* this is seriously bad - should be an emergency */
            if (error_counter < 10 || error_counter % 50 == 0) {
                /* use a counter to prevent flooding (and slowing us down) */
                printf("[px4_simple_app] ERROR return value from poll(): %d
"
                       , poll_ret);
            }

            error_counter++;

        } else {

            if (fds[0].revents & POLLIN) {
                /* obtained data for the first file descriptor */
                struct rw_uart_sonar_data_s sonar;
                /* copy sensors raw data into local buffer */
                orb_copy(ORB_ID(rw_uart_sonar), sonar_sub_fd, &sonar);
                printf("[px4_simple_app] Sonar data:	%s	%d
",
                       sonar.datastr,
                       sonar.data);
            }

            /* there could be more file descriptors here, in the form like:
             * if (fds[1..n].revents & POLLIN) {}
             */
        }
    }
    /*接收数据方式二：end*/

    return 0;
}

  • 编译并刷固件

    • make upload px4fmu-v2_default

  • 在NSH中測试(已加入自启动脚本中)

    • rw_uart start /dev/ttyS2
    • px4_simple_app

  这里写图片描写叙述

3.3 加入系统启动脚本

  能够加入到光流的自己定义启动脚本中：/fs/microsd/etc/extras.txt。

这样随着系统的自启动。rw_uart就会默认启动了。

# start sonar
rw_uart start /dev/ttyS2
【推广】 免费学中医，健康全家人
原文地址：https://www.cnblogs.com/wgwyanfs/p/7325068.html