linux中probe函数传递参数的寻找（下）
通过追寻driver的脚步，我们有了努力的方向：只有找到spi_bus_type的填充device即可，下面该从device去打通，当两个连通之日，也是任督二脉打通之时。先从设备定义去查看，在mach-smdk6410.c中定义了硬件设备信息，从这作为突破口。
/* for mx25lx*/
static void cs_set_level(unsigned line_id, int lvl) {
gpio_direction_output(line_id, lvl);
};
static struct s3c64xx_spi_csinfos3c64xx_spi1_csinfo = {
.fb_delay=0x3,
.line=S3C64XX_GPC(7),
.set_level=cs_set_level,
};
static int mx25lx_ioSetup(struct spi_device*spi)
{
printk(KERN_INFO"mx25lx: setup gpio pins CS and External Int ");
s3c_gpio_setpull(S3C64XX_GPL(8),S3C_GPIO_PULL_UP); //External interrupt from CAN controller
s3c_gpio_cfgpin(S3C64XX_GPL(8),S3C_GPIO_SFN(3)); //External interrupt from CAN controller (hopefully external interrupt)
//s3c_gpio_cfgpin(S3C64XX_GPL(8),S3C_GPIO_INPUT); //External interrupt from CAN controller
s3c_gpio_setpull(S3C64XX_GPC(7),S3C_GPIO_PULL_NONE); // Manual chipselect pin as used in 6410_set_cs
s3c_gpio_cfgpin(S3C64XX_GPC(7),S3C_GPIO_OUTPUT); // Manualchip select pin as used in 6410_set_cs
return0;
}
static struct mx25lx_platform_datamx25lx_info =
{
.oscillator_frequency= 8000000,
.board_specific_setup= mx25lx_ioSetup,
.transceiver_enable= NULL,
.power_enable= NULL,
};
static struct spi_board_info __initdataforlinx6410_mc251x_info[] =
{
{
.modalias= "mcp2515",
.platform_data = &mx25lx_info,
.irq= IRQ_EINT(16),
.max_speed_hz= 10*1000*1000,
.bus_num= 1,
.chip_select= 0,
.mode= SPI_MODE_0,
.controller_data=&s3c64xx_spi1_csinfo,
},
};
struct platform_device s3c64xx_device_spi0= {
.name = "s3c64xx-spi",
.id = 0,
.num_resources =ARRAY_SIZE(s3c64xx_spi0_resource),
.resource =s3c64xx_spi0_resource,
.dev= {
.dma_mask = &spi_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
.platform_data= &s3c64xx_spi0_pdata,
},
};
static struct platform_device*smdk6410_devices[] __initdata =
{
……
/*addby fatfish*/
&s3c64xx_device_spi0,
&s3c64xx_device_spi1,
};
其中platform_device定义为：
struct platform_device {
constchar * name;
int id;
structdevice dev;
u32 num_resources;
structresource * resource;
conststruct platform_device_id *id_entry;
/*MFD cell pointer */
structmfd_cell *mfd_cell;
/*arch specific additions */
structpdev_archdata archdata;
};
初始化函数如下：
static void __initsmdk6410_machine_init(void)
{
……
s3c64xx_spi_set_info(0,0,1);
s3c64xx_spi_set_info(1,0,1);
spi_register_board_info(forlinx6410_mc251x_info,ARRAY_SIZE(forlinx6410_mc251x_info));
……
}
其中的注册板信息的函数如下，后项参数为1，其中board_list为spi.c中定义的全局变量，即：static LIST_HEAD(board_list);。
int __init
spi_register_board_info(structspi_board_info const *info, unsigned n)
{
structboardinfo *bi;
inti;
bi= kzalloc(n * sizeof(*bi), GFP_KERNEL);
if(!bi)
return-ENOMEM;
for(i = 0; i < n; i++, bi++, info++) {
structspi_master *master;
memcpy(&bi->board_info,info, sizeof(*info));
mutex_lock(&board_lock);
list_add_tail(&bi->list,&board_list);
list_for_each_entry(master,&spi_master_list, list)
spi_match_master_to_boardinfo(master,&bi->board_info);
mutex_unlock(&board_lock);
}
return0;
}
其中结果成员如下：
先加锁，然后将board_list加入链接中，在遍历设备，最关键的函数是：
static voidspi_match_master_to_boardinfo(struct spi_master *master,
structspi_board_info *bi)
{
structspi_device *dev;
if(master->bus_num != bi->bus_num)
return;
dev= spi_new_device(master, bi);
if(!dev)
dev_err(master->dev.parent,"can't create new device for %s ",
bi->modalias);
}
spi_new_device作用是实例化一个新设备，定义如下：
struct spi_device *spi_new_device(structspi_master *master,
struct spi_board_info *chip)
{
structspi_device *proxy;
int status;
proxy= spi_alloc_device(master);
if(!proxy)
returnNULL;
……
strlcpy(proxy->modalias,chip->modalias, sizeof(proxy->modalias));
proxy->dev.platform_data = (void *)chip->platform_data;
proxy->controller_data= chip->controller_data;
proxy->controller_state= NULL;
status= spi_add_device(proxy);
if(status < 0) {
spi_dev_put(proxy);
returnNULL;
}
returnproxy;
}
拷贝了platform_data，即mx25lx_info。其中的spi_alloc_device函数定义如下：
struct spi_device *spi_alloc_device(structspi_master *master)
{
structspi_device *spi;
structdevice *dev =master->dev.parent;
if(!spi_master_get(master))
returnNULL;
spi= kzalloc(sizeof *spi, GFP_KERNEL);
if(!spi) {
dev_err(dev,"cannot alloc spi_device ");
spi_master_put(master);
returnNULL;
}
spi->master= master;
spi->dev.parent= dev;
spi->dev.bus= &spi_bus_type;
spi->dev.release= spidev_release;
device_initialize(&spi->dev);
returnspi;
}
在这个定义中将spi_bus_type和dev联系起来，不过此时还没有我们定义的设备信息，设备信息在接下来的赋值中完成。
最后是spi_add_device，将设备信息提交。
int spi_add_device(struct spi_device *spi)
{
staticDEFINE_MUTEX(spi_add_lock);
structdevice *dev = spi->master->dev.parent;
structdevice *d;
intstatus;
……
mutex_lock(&spi_add_lock);
d= bus_find_device_by_name(&spi_bus_type, NULL, dev_name(&spi->dev));
……
status= spi_setup(spi);
if(status < 0) {
dev_err(dev,"can't setup %s, status %d ",
dev_name(&spi->dev),status);
gotodone;
}
……
done:
mutex_unlock(&spi_add_lock);
returnstatus;
}
最终完成将spi_bus_type与定义的device信息联系起来。由于本人才疏学浅，不正确的地方，恳求大牛指正，在此表示感谢