如何 在windows添加一条静态路由
1、添加一条路由表
Route add 60.232.142.40 mask 255.255.255.248 192.168.100.250 metric 3 if 2
添加一条路由记录，所有到60.232.142.40/29网段的数据包，都通过2号接口卡（网卡）走192.168.100.250的网关，优先级为3。（结果会怎样？）
Route add –p 60.232.142.40 mask 255.255.255.248 192.168.100.250 metric 3 if 2
作用同上，只是这是一条长久路由，不会因为重启机器而丢失。
2、删除一条路由表
Route delete 60.232.142.40
请留心：如果有两条路由记录有着相同的“目的网络号”，则会将两条记录同时删除。如果只想删除其中某一条的话，请在删除后用route add命令再添加上其中一条。
From:http://whatislinux.net/how-to-add-a-static-ip-route-in-windows
3、修改一条路由记录
Route change 157.0.0.0 mask 255.0.0.0 157.55.80.5 metric 2 if 2
Change参数只能修改“网关”和“跳数”
---------------------
技术学习/linux学习 2008/04/25 20:28
linux下添加路由的方法：
使用route 命令添加的路由，机器重启或者网卡重启后路由就失效了，方法：
//添加到主机的路由
# route add –host 192.168.168.110 dev eth0
# route add –host 192.168.168.119 gw 192.168.168.1
//添加到网络的路由
# route add –net IP netmask MASK eth0
# route add –net IP netmask MASK gw IP
# route add –net IP/24 eth1
//添加默认网关
# route add default gw IP
//删除路由
# route del –host 192.168.168.110 dev eth0
二：在linux下设置永久路由的方法：
1.在/etc/rc.local里添加
方法：
route add -net 192.168.3.0/24 dev eth0
route add -net 192.168.2.0/24 gw 192.168.3.254
2.在/etc/sysconfig/network里添加到末尾
方法：GATEWAY=gw-ip 或者 GATEWAY=gw-dev
3./etc/sysconfig/static-router :
any net x.x.x.x/24 gw y.y.y.y
|
linux路由的添加对于我们来说很重要，有的时候网络不通，也许就是你路由没加，发出来，希望对大家有所帮助！
服务器ip(eth0)
[root@localhost net]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:0C:29:E3:9A:15
inet addr:172.18.3.205 Bcast:172.18.3.255 Mask:255.255.255.0
inet6 addr: fe80::20c:29ff:fee3:9a15/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4776 errors:0 dropped:0 overruns:0 frame:0
TX packets:3348 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:439384 (429.0 KiB) TX bytes:390425 (381.2 KiB)
Interrupt:11 Base address:0x1400
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:254 errors:0 dropped:0 overruns:0 frame:0
TX packets:254 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:22128 (21.6 KiB) TX bytes:22128 (21.6 KiB)
查看原始路由信息
[root@localhost net]# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
172.18.3.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0
==========================================================
添加默认网关
[root@localhost net]# route add default gw 172.18.3.50
[root@localhost net]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
172.18.3.0 * 255.255.255.0 U 0 0 0 eth0
169.254.0.0 * 255.255.0.0 U 0 0 0 eth0
default 172.18.3.50 0.0.0.0 UG 0 0 0 eth0
=======================================================
添加一个ip(eth0:1)
[root@localhost net]# ifconfig eth0:1 192.168.168.119 netmask 255.255.255.0 up
[root@localhost net]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:0C:29:E3:9A:15
inet addr:172.18.3.205 Bcast:172.18.3.255 Mask:255.255.255.0
inet6 addr: fe80::20c:29ff:fee3:9a15/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5071 errors:0 dropped:0 overruns:0 frame:0
TX packets:3569 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:466532 (455.5 KiB) TX bytes:416538 (406.7 KiB)
Interrupt:11 Base address:0x1400
eth0:1 Link encap:Ethernet HWaddr 00:0C:29:E3:9A:15
inet addr:192.168.168.119 Bcast:192.168.168.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:11 Base address:0x1400
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:258 errors:0 dropped:0 overruns:0 frame:0
TX packets:258 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:22480 (21.9 KiB) TX bytes:22480 (21.9 KiB)
在查看路由信息
[root@localhost net]# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
172.18.3.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
192.168.168.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0
0.0.0.0 172.18.3.50 0.0.0.0 UG 0 0 0 eth0
===============================================================
添加一条到主机192.168.168.110的路由(通过eth0:1)
[root@localhost net]# route add -host 192.168.168.110 dev eth0:1
[root@localhost net]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.168.110 * 255.255.255.255 UH 0 0 0 eth0
172.18.3.0 * 255.255.255.0 U 0 0 0 eth0
192.168.168.0 * 255.255.255.0 U 0 0 0 eth0
169.254.0.0 * 255.255.0.0 U 0 0 0 eth0
default 172.18.3.50 0.0.0.0 UG 0 0 0 eth0
===============================================================
添加一条到主机192.168.168.120的路由(通过ip192.168.168.119)
[root@localhost net]# route add -host 192.168.168.120 gw 192.168.168.119
[root@localhost net]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.168.120 192.168.168.119 255.255.255.255 UGH 0 0 0 eth0
192.168.168.110 * &nb
sp; 255.255.255.255 UH 0 0 0 eth0
172.18.3.0 * 255.255.255.0 U 0 0 0 eth0
192.168.168.0 * 255.255.255.0 U 0 0 0 eth0
169.254.0.0 * 255.255.0.0 U 0 0 0 eth0
default 172.18.3.50 0.0.0.0 UG 0 0 0 eth0
===========================================================
添加到网络的路由(通过eth0)
[root@localhost net]# route add -net 192.168.3.0 netmask 255.255.255.0 dev eth0
[root@localhost net]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.168.120 192.168.168.119 255.255.255.255 UGH 0 0 0 eth0
192.168.168.110 * 255.255.255.255 UH 0 0 0 eth0
192.168.3.0 * 255.255.255.0 U 0 0 0 eth0
172.18.3.0 * 255.255.255.0 U 0 0 0 eth0
192.168.168.0 * 255.255.255.0 U 0 0 0 eth0
169.254.0.0 * 255.255.0.0 U 0 0 0 eth0
default 172.18.3.50 0.0.0.0 UG 0 0 0 eth0
添加到网络的路由(通过ip172.18.3.50)
[root@localhost net]# route add -net 192.168.4.0 netmask 255.255.255.0 gw 172.18.3.50
[root@localhost net]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.168.120 192.168.168.119 255.255.255.255 UGH 0 0 0 eth0
192.168.168.110 * 255.255.255.255 UH 0 0 0 eth0
192.168.4.0 172.18.3.50 255.255.255.0 UG 0 0 0 eth0
192.168.3.0 * 255.255.255.0 U 0 0 0 eth0
172.18.3.0 * 255.255.255.0 U 0 0 0 eth0
192.168.168.0 * 255.255.255.0 U 0 0 0 eth0
169.254.0.0 * 255.255.0.0 U 0 0 0 eth0
default 172.18.3.50 0.0.0.0 UG 0 0 0 eth0
=======================================================================
参数区别-host跟主机ip,-net跟网络号
=======================================================================
输出结果中各个字段的含义是:
Destination表示路由的目标IP地址
Gateway表示网关使用的主机名或者是IP地址。上面输出的"*"表示没有网关
Genmask表示路由的网络掩码
Flags是表示路由的标志。可用的标志及其意义是:U表示路由在启动，H表示target是一台主机，G表示使用网关，R表示对动态路由进行复位设置;D表示动态安装路由，M表示修改路由，!表示拒绝路由。
Metric表示路由的单位开销量
Ref表示依赖本路由现状的其它路由数目
Use表示路由表条目被使用的数目
Iface表示路由所发送的包的目的网络
本文来自思进网：http://www.52sijin.com/ 转载请注明出处！ |