【原创】DE2 实验练习解答—lab4 counters【verilog】【digital logic】

本练习的目的是使用计数器。

Part I 用T触发器实现16-bit的计数器

参照图 1所示的4-bit的同步计数器，实现一个16-bit 的计数器。

005

代码１６－ｂｉｔ　ｃｏｕｎｔｅｒ

1 //top-level file
 2  module part1(KEY0,SW,HEX3,HEX2,HEX1,HEX0);
 3 input KEY0; //时钟脉冲
 4  input [1:0]SW; //使能&复位
 5  output [6:0]HEX3,HEX2,HEX1,HEX0; //输出显示
 6  wire [15:0]q; //16-bit计数输出
 7  
8 counter_16(SW[1],KEY0,SW[0],q);
 9
10 seg7_lut H0(q[3:0],HEX0);
11 seg7_lut H1(q[7:4],HEX1);
12 seg7_lut H2(q[11:8],HEX2);
13 seg7_lut H3(q[15:12],HEX3);
14
15  endmodule
1 //由T触发器构建的16-bit计数器
 2  module counter_16(en,clk,clr,Q);
 3 input en,clk,clr;
 4 wire [15:0]q;
 5 output [15:0]Q;
6 t_ff u0(en,clk,clr,q[0]);
 7 t_ff u1(en&q[0],clk,clr,q[1]);
 8 t_ff u2(en&q[0]&q[1],clk,clr,q[2]);
 9 t_ff u3(en&q[0]&q[1]&q[2],clk,clr,q[3]);
10 t_ff u4(en&q[0]&q[1]&q[2]&q[3],clk,clr,q[4]);
11 t_ff u5(en&q[0]&q[1]&q[2]&q[3]&q[4],clk,clr,q[5]);
12 t_ff u6(en&q[0]&q[1]&q[2]&q[3]&q[4]&q[5],clk,clr,q[6]);
13 t_ff u7(en&q[0]&q[1]&q[2]&q[3]&q[4]&q[5]&q[6],clk,clr,q[7]);
14 t_ff u8(en&q[0]&q[1]&q[2]&q[3]&q[4]&q[5]&q[6]&q[7],clk,clr,q[8]);
15 t_ff u9(en&q[0]&q[1]&q[2]&q[3]&q[4]&q[5]&q[6]&q[7]&q[8],
16 clk,clr,q[9]);
17 t_ff u10(en&q[0]&q[1]&q[2]&q[3]&q[4]&q[5]&q[6]&q[7]&q[8]&q[9],
18 clk,clr,q[10]);
19 t_ff u11(en&q[0]&q[1]&q[2]&q[3]&q[4]&q[5]&q[6]&q[7]&q[8]&q[9]&q[10],
20 clk,clr,q[11]);
21 t_ff u12(en&q[0]&q[1]&q[2]&q[3]&q[4]&q[5]&q[6]&q[7]&q[8]&q[9]&q[10]&q[11],
22 clk,clr,q[12]);
23 t_ff u13(en&q[0]&q[1]&q[2]&q[3]&q[4]&q[5]&q[6]&q[7]&q[8]&q[9]&q[10]&q[11]&q[12],
24 clk,clr,q[13]);
25 t_ff u14(en&q[0]&q[1]&q[2]&q[3]&q[4]&q[5]&q[6]&q[7]&q[8]&q[9]&q[10]&q[11]&q[12]&q[13],
26 clk,clr,q[14]);
27 t_ff u15(en&q[0]&q[1]&q[2]&q[3]&q[4]&q[5]&q[6]&q[7]&q[8]&q[9]&q[10]&q[11]&q[12]&q[13]&q[14],
28 clk,clr,q[15]);
29
30 assign Q=q;
31
32  endmodule
1 //T flip flop
 2  module t_ff(t,clk,rst_n,q);
 3 input t,clk,rst_n;
 4 outputreg q;
 5
6 always @(posedge clk)
 7 begin
 8 if(!rst_n)
 9 q<=0;
10 else
11 begin
12 if(t==1'b1)
13   q<=~q;
14 else
15 q<=q;
16 end
17 end
18
19  endmodule

001

图２　Ｆｍａｘ值

002

图３　占用的ＬＥ数量

 

 

Part　ＩＩ　用赋值语句实现１６-ｂｉｔ计数器

代码

1 //counter-16bit
 2  module part2(clk,rst_n,q);
 3 input clk,rst_n;
 4 outputreg [15:0]q;
 5
6 always @(posedge clk)
 7 begin
8 if(!rst_n)
 9 q<=1'b0;
10  else
11 begin
12 if(q==65535)
13 q<=0;
14 else
15 q<=q+1;
16 end
17 end
18
19  endmodule

001

图４　１６-ｂｉｔ计数器的ＲＴＬ视图

002

图５　Ｆｍａｘ值

003

图６　１６-ｂｉｔ计数器占用的ＬＥ

 

Part　ＩＩＩ　用ＬＰＭ实现１６-ｂｉｔ计数器

代码

1 //Top-level file
2  module counter_lpm(en,clk,clr,q);
3 input en,clk,clr;
4 output [15:0]q;
5
6 megcounter counter_16bit(.clock(clk),.cnt_en(en),.sclr(clr),
7 .q(q)
8 );
9 endmodule
1 // synopsys translate_off
 2 `timescale 1 ps /1 ps
 3 // synopsys translate_on
 4 module megcounter (
 5 clock,
 6 cnt_en,
 7 sclr,
 8 q);
 9
10 input clock;
11 input cnt_en;
12 input sclr;
13 output [15:0] q;
14
15 wire [15:0] sub_wire0;
16 wire [15:0] q = sub_wire0[15:0];
17
18 lpm_counter lpm_counter_component (
19 .sclr (sclr),
20 .clock (clock),
21 .cnt_en (cnt_en),
22 .q (sub_wire0),
23 .aclr (1'b0),
24 .aload (1'b0),
25 .aset (1'b0),
26 .cin (1'b1),
27 .clk_en (1'b1),
28 .cout (),
29 .data ({16{1'b0}}),
30 .eq (),
31 .sload (1'b0),
32 .sset (1'b0),
33 .updown (1'b1));
34 defparam
35 lpm_counter_component.lpm_direction ="UP",
36 lpm_counter_component.lpm_port_updown ="PORT_UNUSED",
37 lpm_counter_component.lpm_type ="LPM_COUNTER",
38 lpm_counter_component.lpm_width =16;
39
40
41 endmodule

001

图７　用ＬＰＭ实现１６-ｂｉｔ计数器所占用的ＬＥ

Part　ＩＶ　循环显示０-９

在ＨＥＸ０上循环显示０-９，每秒刷新一次。

代码

1 //top-level file
 2 module seg_number(
 3 output [6:0]HEX0,
 4 input CLOCK_50,
 5 input [0:0]KEY
 6 );
 7
8 wire clk_1hz;
 9 reg [3:0]cnt;
 10
11 div u0(
 12 .o_clk(clk_1hz),
 13 .i_clk(CLOCK_50),
 14 .rst_n(KEY)
 15 );
 16
17 always @(posedge clk_1hz ornegedge KEY)
 18 begin
 19 if(!KEY)
 20 cnt<=4'b0;
 21 else
22 begin
 23 if(cnt==4'd9)
 24 cnt<=4'b0;
 25 else
 26 cnt<=cnt+1'b1;
 27 end
 28 end
 29
30 seg7_lut u1(
 31 .oseg(HEX0),
 32 .idig(cnt[3:0])
 33 );
 34 endmodule
 35
36 //divider
 37 module div(
 38 outputreg o_clk,
 39 input rst_n,
 40 input i_clk
 41 );
 42
43 parameter N=50_000_000;
 44 parameter M=24_999_999;
 45
46 reg [25:0]cnt;
 47
48 always @(posedge i_clk ornegedge rst_n)
 49 begin
 50 if(!rst_n)
 51 cnt<=26'b0;
 52 else
 53 begin
 54 if(cnt==N-1)
 55 cnt<=26'b0;
 56 else
 57 cnt<=cnt+26'b1;
 58 end
 59 end
 60 always @(posedge i_clk ornegedge rst_n)
 61 begin
 62 if(!rst_n)
 63 o_clk<=0;
 64 else
 65 begin
 66 if(cnt<=M)
 67 o_clk<=1;
 68 else
 69 o_clk<=0;
 70 end
 71 end
 72
73 endmodule
 74
75 //seg7_lut
 76 module seg7_lut (
 77 outputreg [6:0] oseg,
 78 input [3:0] idig
 79 );
 80 always @ (idig)
 81 begin
 82 case (idig)
 83 4'h1: oseg = 7'b1111001; // ---t---
 84 4'h2: oseg = 7'b0100100; // | |
 85 4'h3: oseg = 7'b0110000; // lt rt
 86 4'h4: oseg = 7'b0011001; // | |
 87 4'h5: oseg = 7'b0010010; // ---m---
 88 4'h6: oseg = 7'b0000010; // | |
 89 4'h7: oseg = 7'b1111000; // lb rb
 90 4'h8: oseg = 7'b0000000; // | |
 91 4'h9: oseg = 7'b0011000; // ---b---
 92 4'ha: oseg = 7'b0001000;
 93 4'hb: oseg = 7'b0000011;
 94 4'hc: oseg = 7'b1000110;
 95 4'hd: oseg = 7'b0100001;
 96 4'he: oseg = 7'b0000110;
 97 4'hf: oseg = 7'b0001110;
 98 default: oseg =7'b1000000;
 99 endcase
100 end
101 endmodule

Part　Ｖ　循环显示ＨＥＬＬＯ

在ＨＥＸ７－ＨＥＸ０上循环显示ＨＥＬＬＯ，如图８所示。

001

图８　８个７ｓｅｇｍｅｎｔ上循环显示ＨＥＬＬＯ

代码

top-level file
1 //top-level file
 2 module hello(HEX7,HEX6,HEX5,HEX4,
 3 HEX3,HEX2,HEX1,HEX0,
 4 CLOCK_50,KEY);
 5 input CLOCK_50;
 6 input [0:0]KEY;
 7 output [6:0]HEX7,HEX6,HEX5,HEX4,HEX3,HEX2,
 8 HEX1,HEX0;
 9
10 wire clk_1hz;
11 reg [3:0]cnt;
12
13 div u0(.o_clk(clk_1hz),
14 .rst_n(KEY),
15 .i_clk(CLOCK_50)
16 );
17
18 always @(posedge clk_1hz ornegedge KEY)
19 begin
20 if(!KEY)
21 cnt<=4'b0;
22 else
23 begin
24 if(cnt==4'b0111)
25 cnt<=4'b0;
26 else
27 cnt<=cnt+1'b1;
28 end
29 end
30
31 seg7_h0 h0(.oseg(HEX0),
32 .idig(cnt)
33 );
34 seg7_h1 h1(.oseg(HEX1),
35 .idig(cnt)
36 );
37 seg7_h2 h2(.oseg(HEX2),
38 .idig(cnt)
39 );
40 seg7_h3 h3(.oseg(HEX3),
41 .idig(cnt)
42 );
43 seg7_h4 h4(.oseg(HEX4),
44 .idig(cnt)
45 );
46 seg7_h5 h5(.oseg(HEX5),
47 .idig(cnt)
48 );
49 seg7_h6 h6(.oseg(HEX6),
50 .idig(cnt)
51 );
52 seg7_h7 h7(.oseg(HEX7),
53 .idig(cnt)
54 );
55 endmodule
分频器
1 //divider
 2 module div(
 3 outputreg o_clk,
 4 input rst_n,
 5 input i_clk
 6 );
 7
8 parameter N=50_000_000;
 9 parameter M=24_999_999;
10
11 reg [25:0]cnt;
12
13 always @(posedge i_clk ornegedge rst_n)
14 begin
15 if(!rst_n)
16 cnt<=26'b0;
17 else
18 begin
19 if(cnt==N-1)
20 cnt<=26'b0;
21 else
22 cnt<=cnt+26'b1;
23 end
24 end
25 always @(posedge i_clk ornegedge rst_n)
26 begin
27 if(!rst_n)
28 o_clk<=0;
29 else
30 begin
31 if(cnt<=M)
32 o_clk<=1;
33 else
34 o_clk<=0;
35 end
36 end
37
38 endmodule
译码0
1 //seg7_lut
 2 module seg7_h0
 3 (
 4 outputreg [6:0] oseg,
 5 input [3:0] idig
 6 );
 7 always @ (idig)
 8 begin
 9 case (idig)
10 4'h0: oseg = 7'b1000000; //O
11 //4'h1: oseg = 7'b1111001;
12 //4'h2: oseg = 7'b0100100;
13 //4'h3: oseg = 7'b0110000;
14 4'h4: oseg = 7'b0001001; //H
15 4'h5: oseg = 7'b0000110; //E
16 4'h6: oseg = 7'b1000111; //L
17 4'h7: oseg = 7'b1000111; //L
18
19 default: oseg =7'b1111111;
20 endcase
21 end
22 endmodule
译码1
1 //seg7_lut
 2 module seg7_h1
 3 (
 4 outputreg [6:0] oseg,
 5 input [3:0] idig
 6 );
 7 always @ (idig)
 8 begin
 9 case (idig)
10 4'h1: oseg = 7'b1000000; //O
11 //4'h4: oseg = 7'b1111001;
12 //4'h2: oseg = 7'b0100100;
13 //4'h3: oseg = 7'b0110000;
14 4'h5: oseg = 7'b0001001; //H
15 4'h6: oseg = 7'b0000110; //E
16 4'h7: oseg = 7'b1000111; //L
17 4'h0: oseg = 7'b1000111; //L
18
19 default: oseg =7'b1111111;
20 endcase
21 end
22 endmodule

共8个译码模块（略6）

解法2

  1 module part5(CLOCK_50,HEX7,HEX6,HEX5,HEX4,HEX3,HEX2,HEX1,HEX0);
  2     input CLOCK_50;
  3     output reg [6:0] HEX7,HEX6,HEX5,HEX4,HEX3,HEX2,HEX1,HEX0;
  4     
  5     parameter blank=7'b1_111_111,
  6                 H=7'b0_001_001,
  7                 E=7'b0_000_110,
  8                 L=7'b1_000_111,
  9                 O=7'b1_000_000;
 10                 
 11     wire clk_1hz;
 12     wire [3:0] cnt;
 13     
 14     div u0(CLOCK_50,clk_1hz,1'b1);
 15     counter8 u1(clk_1hz,1'b1,cnt);
 16     
 17     always @(cnt)
 18     case(cnt)
 19         4'd0:begin
 20                 HEX7=blank;
 21                 HEX6=blank;
 22                 HEX5=blank;
 23                 HEX4=H;
 24                 HEX3=E;
 25                 HEX2=L;
 26                 HEX1=L;
 27                 HEX0=O;
 28             end
 29         4'd1:begin
 30                 HEX0=blank;
 31                 HEX7=blank;
 32                 HEX6=blank;
 33                 HEX5=H;
 34                 HEX4=E;
 35                 HEX3=L;
 36                 HEX2=L;
 37                 HEX1=O;
 38             end    
 39         4'd2:begin
 40                 HEX1=blank;
 41                 HEX0=blank;
 42                 HEX7=blank;
 43                 HEX6=H;
 44                 HEX5=E;
 45                 HEX4=L;
 46                 HEX3=L;
 47                 HEX2=O;
 48             end    
 49         4'd3:begin
 50                 HEX2=blank;
 51                 HEX1=blank;
 52                 HEX0=blank;
 53                 HEX7=H;
 54                 HEX6=E;
 55                 HEX5=L;
 56                 HEX4=L;
 57                 HEX3=O;
 58             end    
 59         4'd4:begin
 60                 HEX3=blank;
 61                 HEX2=blank;
 62                 HEX1=blank;
 63                 HEX0=H;
 64                 HEX7=E;
 65                 HEX6=L;
 66                 HEX5=L;
 67                 HEX4=O;
 68             end    
 69         4'd5:begin
 70                 HEX4=blank;
 71                 HEX3=blank;
 72                 HEX2=blank;
 73                 HEX1=H;
 74                 HEX0=E;
 75                 HEX7=L;
 76                 HEX6=L;
 77                 HEX5=O;
 78             end    
 79         4'd6:begin
 80                 HEX5=blank;
 81                 HEX4=blank;
 82                 HEX3=blank;
 83                 HEX2=H;
 84                 HEX1=E;
 85                 HEX0=L;
 86                 HEX7=L;
 87                 HEX6=O;
 88             end            
 89         4'd7:begin
 90                 HEX6=blank;
 91                 HEX5=blank;
 92                 HEX4=blank;
 93                 HEX3=H;
 94                 HEX2=E;
 95                 HEX1=L;
 96                 HEX0=L;
 97                 HEX7=O;
 98             end    
 99     endcase
100     
101 endmodule        
102

其实还可以利用字型码加1的方法。

Conclusion

Ｐａｒｔ１　有助于理解计数器的具体实现，Ｐａｒｔ４是Ｐａｒｔ５的基础，单个７segment循环显示操作成功，多个

自然不难。：）

Reference

《Using　library　modules　ｉｎ　Verilog　Designｓ　》

【推广】 免费学中医，健康全家人
原文地址：https://www.cnblogs.com/halflife/p/1751214.html