|
lspci is a utility for displaying information about PCI buses in the system and devices connected to them.
The following tags are definedBy default, it shows a brief list of devices. Use the options described below to request either a more verbose output or output intended for parsing by other programs. # lspci00:00.0 Host bridge: Intel Corporation 5520 I/O Hub to ESI Port (rev 22)...00:16.7 System peripheral: Intel Corporation 5520/5500/X58 Chipset QuickData Technology Device (rev 22)00:1a.0 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4...00:1d.7 USB controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1...0b:00.1 Ethernet controller: Broadcom Corporation NetXtreme II BCM5709 Gigabit Ethernet (rev 20)15:00.0 Fibre Channel: QLogic Corp. ISP2532-based 8Gb Fibre Channel to PCI Express HBA (rev 02)15:00.1 Fibre Channel: QLogic Corp. ISP2532-based 8Gb Fibre Channel to PCI Express HBA (rev 02)1f:00.0 Ethernet controller: Mellanox Technologies MT26448 [ConnectX EN 10GigE, PCIe 2.0 5GT/s] (rev b0)This example shows device in the slot # lspci -s 1f:00.01f:00.0 Ethernet controller: Mellanox Technologies MT26448 [ConnectX EN 10GigE, PCIe 2.0 5GT/s] (rev b0) -s [[[[<domain>]:]<bus>]:][<slot>][.[<func>]] Show only devices in the specified domain (in case your machine has several host bridges, they can either share a common bus number space or each of them can address a PCI domain of its own; domains are numbered from 0 to ffff), bus (0 to ff), slot (0 to 1f) and function (0 to 7). Each component of the device address can be omitted or set to "*", both meaning "any value". All numbers are hexadecimal. E.g., "0:" means all devices on bus 0, "0" means all functions of device 0 on any bus, "0.3" selects third function of device 0 on all buses and ".4" shows only the fourth function of each device.This example shows device verbose output, a sequence of records separated by blank lines. Each line containing a single 'tag: value' pair # lspci -vmms 1f:00.0Slot: 1f:00.0Class: Ethernet controllerVendor: Mellanox TechnologiesDevice: MT26448 [ConnectX EN 10GigE, PCIe 2.0 5GT/s]SVendor: Mellanox TechnologiesSDevice: Device 0013PhySlot: 4Rev: b0-mm Dump PCI device data in a machine readable form for easy parsing by scripts. -n Show PCI vendor and device codes as numbers instead of looking them up in the PCI ID list, useful for scripting and programing # lspci -nvmms 1f:00.0Slot: 1f:00.0Class: 0200Vendor: 15b3Device: 6750SVendor: 15b3SDevice: 0013PhySlot: 4Rev: b0 Slot The name of the slot where the device resides ([domain:]bus:device.function). This tag is always the first in a record. Class Name of the class. Vendor Name of the vendor. Device Name of the device. SVendor Name of the subsystem vendor (optional). SDevice Name of the subsystem (optional). PhySlot The physical slot where the device resides (optional, Linux only). Rev Revision number (optional). ProgIf Programming interface (optional). Driver Kernel driver currently handling the device (optional, Linux only). Module Kernel module reporting that it is capable of handling the device (optional, Linux only).Show kernel module of a device
# lspci -ks 1f:00.01f:00.0 Ethernet controller: Mellanox Technologies MT26448 [ConnectX EN 10GigE, PCIe 2.0 5GT/s] (rev b0) Subsystem: Mellanox Technologies Device 0013 Kernel driver in use: mlx4_core Kernel modules: mlx4_core, mlx4_enThere is also a easy way to run lspci if you don't mind to search things in a big output -v Be verbose and display detailed information about all devices. -vv Be very verbose and display more details. This level includes everything deemed useful. -vvv Be even more verbose and display everything we are able to parse, even if it doesn't look interesting at all (e.g., undefined memory regions).Pretty much everything you need are here, including device part number
# lspci -vvvs 1f:00.01f:00.0 Ethernet controller: Mellanox Technologies MT26448 [ConnectX EN 10GigE, PCIe 2.0 5GT/s] (rev b0) Subsystem: Mellanox Technologies Device 0013 Physical Slot: 4 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 30 Region 0: Memory at 97a00000 (64-bit, non-prefetchable) [size=1M] Region 2: Memory at fb800000 (64-bit, prefetchable) [size=8M] Expansion ROM at <ignored> [disabled] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [48] Vital Product Data Product Name: Hawk Dual Port Read-only fields: [PN] Part number: 81Y1540 [EC] Engineering changes: A3 [SN] Serial number: 81Y1540YK502000045L [V0] Vendor specific: PCIe Gen2 x8 [RV] Reserved: checksum good, 0 byte(s) reserved Read/write fields: [V1] Vendor specific: N/A [YA] Asset tag: N/A [RW] Read-write area: 106 byte(s) free End Capabilities: [9c] MSI-X: Enable+ Count=128 Masked- Vector table: BAR=0 offset=0007c000 PBA: BAR=0 offset=0007d000 Capabilities: [60] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 unlimited ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- FLReset- MaxPayload 256 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #8, Speed 5GT/s, Width x8, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s, Width x8, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported DevCtl2: Completion Timeout: 260ms to 900ms, TimeoutDis-, LTR-, OBFF Disabled LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [100 v1] Alternative Routing-ID Interpretation (ARI) ARICap: MFVC- ACS-, Next Function: 0 ARICtl: MFVC- ACS-, Function Group: 0 Capabilities: [148 v1] Device Serial Number 00-02-c9-03-00-4f-68-7e Kernel driver in use: mlx4_core Kernel modules: mlx4_core, mlx4_enIf you know verdor code and device code, then you can search the device slot and other info, it seems not useful, but in scripting, it's useful. # lspci -vmmd 1077:2532Slot: 15:00.0Class: Fibre ChannelVendor: QLogic Corp.Device: ISP2532-based 8Gb Fibre Channel to PCI Express HBASVendor: QLogic Corp.SDevice: Device 015dPhySlot: 2Rev: 02Slot: 15:00.1Class: Fibre ChannelVendor: QLogic Corp.Device: ISP2532-based 8Gb Fibre Channel to PCI Express HBASVendor: QLogic Corp.SDevice: Device 015dPhySlot: 2Rev: 02For more info about sysfs filesystem
https://www.kernel.org/pub/linux/kernel/people/mochel/doc/papers/ols-2005/mochel.pdf |